pcy155

Discussions related to MegaDrum Hardware

pcy155

Postby Chairapta » Tue Jul 12, 2016 8:24 am

Hello everyone,
I have a little problem with my PCY155 .
I clearly distinguished the three areas, but the first hit i give on the bow is always captured as a hit on the edge. The hits that follow are correct.
How can I fix this?
thank you
Chairapta
 
Posts: 39
Joined: Sat May 14, 2016 7:11 am

Re: pcy155

Postby dmitri » Tue Jul 12, 2016 2:34 pm

1. Are you using the latest firmware version?
2. Please post a screenshot of your settings for the cymbal.
dmitri
Site Admin
 
Posts: 8706
Joined: Fri Aug 03, 2007 8:05 pm

Re: pcy155

Postby Chairapta » Wed Jul 13, 2016 10:35 am

Chairapta
 
Posts: 39
Joined: Sat May 14, 2016 7:11 am

Re: pcy155

Postby dmitri » Wed Jul 13, 2016 3:53 pm

I first would suggest to set MinScan on the Edge (Switch) equal or lower then MinScan on the Bow.
dmitri
Site Admin
 
Posts: 8706
Joined: Fri Aug 03, 2007 8:05 pm

Re: pcy155

Postby Chairapta » Thu Jul 14, 2016 8:06 am

ok , tested , but without effect , Bminscan 30 and Eminscan 20 .
I no longer picks up the bow now .
Chairapta
 
Posts: 39
Joined: Sat May 14, 2016 7:11 am

Re: pcy155

Postby dmitri » Thu Jul 14, 2016 2:51 pm

Ok, I will re-test it with my PCY155. My house is in a mess state right now so it will take awhile.
dmitri
Site Admin
 
Posts: 8706
Joined: Fri Aug 03, 2007 8:05 pm

Re: pcy155

Postby Chairapta » Sun Jul 17, 2016 10:17 am

I noticed it was when the mode "alt sampling algorithm" was enabled.
my toms do actually work well in this mode .
Chairapta
 
Posts: 39
Joined: Sat May 14, 2016 7:11 am

Re: pcy155

Postby Chairapta » Tue Jul 19, 2016 6:47 pm

I thought I understood the setup of cymbal , but I realize that I am far away.
I lose hope.

I have 3 Yamaha : hh135 pcy 135 and PCY155 .
With my multimeter ,
When I measure for pcy, i have 0 ohm between ring and sleeve when i press the bell switch and 9,62 kohm when i press de edge.


this is what I measure. There are 3 parts .
The first is on the bow , the second on the bell and the last on the edge .
The first line shows the signal between tip and sleeve .
The second line , the signal between ring and sleeve .
Image

It is clear that there is no signal at the beginning between ring and sleeve, during the first wave of the bow. But on the other, yes
So I think my cymbal work.
what am I doing wrong?
Chairapta
 
Posts: 39
Joined: Sat May 14, 2016 7:11 am

Re: pcy155

Postby Tatoupulus » Wed Jul 20, 2016 1:30 pm

Hi!
Here are my settings for the Yamaha-Ride - maybe this helps. For me it's working fine.
You do not have the required permissions to view the files attached to this post.
Tatoupulus
 
Posts: 26
Joined: Mon Mar 03, 2014 11:47 am

Re: pcy155

Postby Chairapta » Wed Jul 20, 2016 1:53 pm

thank you , I'll test .
Do you have the " alt sampling algorithm " checked ? without activating it , i'm at a threshold of 32 , and I see that you are only 8.
Chairapta
 
Posts: 39
Joined: Sat May 14, 2016 7:11 am

Next

Return to MegaDrum Hardware

Who is online

Users browsing this forum: No registered users and 112 guests