>>> KIT AVAILABLE <<< All In One v2.8 PCB Kit to sell !

[Synthex]

PCB looks great Synthex, how about the atmega644, have they shown yet?

Atmega644 is now available.

[Synthex]

Some news here :

http://www.megadrum.info/forums/viewtopic.php?f=3&t=813

[kurtus420]

Thanks Synthex, I'll send you my revised list of parts.

PCB looks great Synthex, how about the atmega644, have they shown yet?

Atmega644 is now available.

[hyeatman]

I'm sorry but I am not sure this is reaching the proper person. I would like to purchase your new version v3.1
- Up to 56 inputs !
- New dimension : 120mm x 100mm
- Use of 18F14K50 for USB

I would like to purchase the new Kit #3 (full kit) PCB v3.1 + PCB Components + Displays + Buttons :
My shipping address is:

Hoyt Yeatman
11526 Sumac Lane
Santa Rosa Valley Ca. 93012
USA.

I would like to pay via Paypal.

I'm sorry if I have posted you twice

Best,
Hoyt

[kurtus420]

You need to pm Synthex all of this info and he will give you the detail.

I'm sorry but I am not sure this is reaching the proper person. I would like to purchase your new version v3.1
- Up to 56 inputs !
- New dimension : 120mm x 100mm
- Use of 18F14K50 for USB

I would like to purchase the new Kit #3 (full kit) PCB v3.1 + PCB Components + Displays + Buttons :
My shipping address is:

Hoyt Yeatman
11526 Sumac Lane
Santa Rosa Valley Ca. 93012
USA.

I would like to pay via Paypal.

I'm sorry if I have posted you twice

Best,
Hoyt

[CyberFly]

What should I do with these connections:

2 - HiHat controller High impedance input
3 - HiHat controller Power source
4 - HiHat controller Low impedance input

What is the effect of high or low impedance?

What does to power source do? Is this used for a high hat pedal with a resistor?
And could it be used to used to power a LED for an optical high hat controller?

[Synthex]

High impedance HiHat pedal is a pedal with a potentiometer over 100Kohms.
Low impedance HiHat pedal is a pedal with a potentiometer below 100Kohms.

The optical HH controller is a low output impedance pedal.
http://www.megadrum.info/forums/viewtopic.php?f=3&t=422&start=80#p7035

[synco]

hello.i have a really stupid question:how does the pc recognise the drum kit?as a sound card or how can go from hitting the pads to hearing the sounds in the speakers?do i have to use a special software?

[Bulok]

HI

You need to use prgramme with audio sound kit of drums ( or other instruments midi ^^ )

I use ezDrummer for the sound, it's very good.
But the kit is predefined and we cannot modify at will.

A master software is also needed because to ezdrummer is only an add-on.
As master software I use Cubase 4 who was delivered with my mixing desk.
That works tres indeed. There is a video on my youtube:

Part 1 - Making : http://www.youtube.com/watch?v=C2cky6sOLqU

Part 2 - Playing : http://www.youtube.com/watch?v=BVqYV009hho

[CyberFly]

How should I connect the hi hat input?
2 - HiHat controller High impedance input
3 - HiHat controller Power source
4 - HiHat controller Low impedance input

For drums I connect the pins like this:
Tip = head
Ring = rim
Sleeve = ground

Should the hi hat controller go like this?
Tip = 2 - HiHat controller High impedance input
Ring = 3 - HiHat controller Power source
Sleeve = 4 - HiHat controller Low impedance input