VH12 configuration

[dmitri]

In a few minutes I'll post another firmware to test.

[dmitri]

Please, load this firmware:

megadrum_20121206_1.zip

and repeat this test - http://www.megadrum.info/forums/viewtop ... 584#p22584 - on the low impedance input with and without a resistor. You must set LowLevel to the lowest level(11) and also you may want to set HiLevel to 1023 to prevent exiting the menu accidentally.

[ibanman555]

Please, load this firmware:

megadrum_20121206_1.zip

and repeat this test - viewtopic.php?p=22584#p22584 - on the low impedance input with and without a resistor. You must set LowLevel to the lowest level(11) and also you may want to set HiLevel to 1023 to prevent exiting the menu accidentally.

This is with 20121206

*No resistor*
Lo Imp
AltIn - No
CC RdcLvl - 0
LevelsAuto - No

LowLevel and HiLevel are at their absolute Low and Hi levels...
The "raw level" shows 294 in the fully open position. It is steady for a 5 seconds, then jumps to 309, and back again.

At 80% - 50% 244-260, jumping back and forth...

40% - 10% 241-249, jumping back and forth...

0% (fully closed) shows 241-249, jumping back and forth in the fully closed position.

Applying pressure (practically standing on the pedal) I can reach 237-239

[dmitri]

Once you've done the test with the resistor, please repeat the test again:
1. without a resistor and RdcLvl set to 1
2. with a resistor and RdcLvl set to 3

[ibanman555]

Once you've done the test with the resistor, please repeat the test again:
1. without a resistor and RdcLvl set to 1
2. with a resistor and RdcLvl set to 3

This is with 20121206

*With 10k Resistor*
Lo Imp
AltIn - No
CC RdcLvl - 0
LevelsAuto - No

LowLevel and HiLevel are at their absolute Low and Hi levels...
The "raw level" shows 1012 in the fully open position. It is steady.

80% - 964 - 981, not steady.
60% - 924 - 933, not steady.
40% - 909 - 915, not steady.
20% - 900 - 909, not steady.
0% (fully closed) shows 885 - 886, jumping back and forth in the fully closed position.
Applying pressure (practically standing on the pedal) I can reach 361-365


with a resistor and RdcLvl set to 3
*With 10k Resistor*
Lo Imp
AltIn - No
CC RdcLvl - 3
LevelsAuto - No

LowLevel and HiLevel are at their absolute Low and Hi levels...
The "raw level" shows 1012 in the fully open position. It is steady.

80% - 955, dropping to 902 after 5 seconds.
60% - 933, dropping to 884 every few seconds.
40% - 868 -920, not steady.
20% - 854, raising to 902 after a good 10 to 15 seconds.
0% (fully closed) shows 886, steady.
Applying pressure (practically standing on the pedal) I can reach 373, it is steady.


without a resistor and RdcLvl set to 1
Lo Imp
AltIn - No
CC RdcLvl - 1
LevelsAuto - No

LowLevel and HiLevel are at their absolute Low and Hi levels...
The "raw level" shows 293 in the fully open position. It is steady.

80% - 10% 244, it is steady.

0% (fully closed) shows 244, steady.
Applying pressure (practically standing on the pedal) I can reach 244, it is steady. Continuing to fully open and close the pedal, it does not always return to 244 (sometimes 239, 245, 241 etc)

[dmitri]

Please, load this firmware:

megadrum_20121206_2.zip

and repeat last test:
1. without a resistor and RdcLvl=1.
2. with a resistor and RdcLvl=3.

LowLevel must be set to 11 and HiLevel must be set to 1023.

[ibanman555]

Please, load this firmware:

megadrum_20121206_2.zip

and repeat last test:
1. without a resistor and RdcLvl=1.
2. with a resistor and RdcLvl=3.

LowLevel must be set to 11 and HiLevel must be set to 1023.

without a resistor and RdcLvl set to 1
Lo Imp
AltIn - No
CC RdcLvl - 1
LevelsAuto - No

LowLevel and HiLevel are at their absolute Low and Hi levels...
The "raw level" shows 293 in the fully open position. It is steady.

80% - 10% 244 - 248, jumping back and forth.

0% (fully closed) shows 243- 244, jumping back and forth.
Applying pressure (practically standing on the pedal) I can reach 239-227, it is not steady.

with a resistor and RdcLvl=3
Lo Imp
AltIn - No
CC RdcLvl - 3
LevelsAuto - No

LowLevel and HiLevel are at their absolute Low and Hi levels...
The "raw level" shows 1012 in the fully open position. It is steady.

80% - 973, dropping to 913 after 5 seconds.
60% - 949, dropping to 941 every few seconds.
40% - 924, dropping to 844 every few seconds.
20% - 913, raising to 909 after 5 seconds.
0% (fully closed) shows 892 - 846, bouncing between the two.
Applying pressure (practically standing on the pedal) I can reach 380, it is steady.

[dmitri]

Please, load this firmware:

megadrum_20121206_3.zip

and repeat last test:
1. without a resistor and RdcLvl=0.
2. with a resistor and RdcLvl=3.

[ibanman555]

Please, load this firmware:

megadrum_20121206_3.zip

and repeat last test:
1. without a resistor and RdcLvl=0.
2. with a resistor and RdcLvl=3.

with a resistor and RdcLvl=3
Lo Imp
AltIn - No
CC RdcLvl - 3
LevelsAuto - No

LowLevel and HiLevel are at their absolute Low and Hi levels...
The "raw level" shows 998 in the fully open position. It is steady.

80% - 953, it is steady .
60% - 912, it is steady.
40% - 907 steady.
20% - again 907 steady.
0% (fully closed) 892 steady.
Applying pressure (practically standing on the pedal) I can reach 361, it is steady.


without a resistor and RdcLvl=0
Lo Imp
AltIn - No
CC RdcLvl - 0
LevelsAuto - No

LowLevel and HiLevel are at their absolute Low and Hi levels...
The "raw level" shows 293-295 in the fully open position. it is not steady .

80% -0% 249, dropping to 242 after a few seconds.
Applying pressure (practically standing on the pedal) I can reach 229-234, it is not steady.

[ibanman555]

Dmitri,

I need to retire from testing this evening due to a prior engagement. I will continue later this evening when I return and do whatever you need for tomorrow. Thanks!!