PCB DESIGN - All In One v2.5 - 32 inputs with 74HC4851

Discussions related to MegaDrum Hardware

Re: PCB DESIGN - All In One v2.5 - 32 inputs with 74HC4851

Postby jman 31 » Wed Oct 07, 2009 5:14 pm

mrdutx wrote:today i'm done doing pcb board..but it not finished. the was problem in the process. i printed the pcb layout from dmitri..here the film that i use.
this circuit is very complex!
the problem is..after done the developer process.
the circle in the pcb is the problem ..can anyone tell me why this happen and what are the solution.
the line is too close


I had the same problem when I did it using the toner transfer method. I ended up using a sharp knife and cutting between the traces to make sure there were no shorts after it had been etched.
jman 31
 
Posts: 536
Joined: Thu Jul 10, 2008 10:51 pm
Location: USA

Re: PCB DESIGN - All In One v2.5 - 32 inputs with 74HC4851

Postby japi » Wed Oct 07, 2009 5:29 pm

I highly recommend buying a pcb done by synthex. You will have too less hassle that way, and still you need to solder components, upload firmware, etc, so still will be a little DIY
:D
japi
 
Posts: 180
Joined: Tue Oct 07, 2008 2:03 pm
Location: Buenos Aires, Argentina

Re: PCB DESIGN - All In One v2.5 - 32 inputs with 74HC4851

Postby mrdutx » Wed Oct 07, 2009 5:32 pm

japi wrote:I highly recommend buying a pcb done by synthex. You will have too less hassle that way, and still you need to solder components, upload firmware, etc, so still will be a little DIY
:D

i love to buy it. but i don't have pay pal and live in malaysia. it pretty hard to me to buy it.
mrdutx
 
Posts: 23
Joined: Wed Sep 23, 2009 3:57 am

Re: PCB DESIGN - All In One v2.5 - 32 inputs with 74HC4851

Postby mrdutx » Wed Oct 07, 2009 5:32 pm

jman 31 wrote:
mrdutx wrote:today i'm done doing pcb board..but it not finished. the was problem in the process. i printed the pcb layout from dmitri..here the film that i use.
this circuit is very complex!
the problem is..after done the developer process.
the circle in the pcb is the problem ..can anyone tell me why this happen and what are the solution.
the line is too close


I had the same problem when I did it using the toner transfer method. I ended up using a sharp knife and cutting between the traces to make sure there were no shorts after it had been etched.


it's working?
mrdutx
 
Posts: 23
Joined: Wed Sep 23, 2009 3:57 am

Re: PCB DESIGN - All In One v2.5 - 32 inputs with 74HC4851

Postby Synthex » Wed Oct 07, 2009 5:49 pm

mrdutx wrote:i love to buy it. but i don't have pay pal and live in malaysia. it pretty hard to me to buy it.

You can pay by bank transfer if you want.
Synthex
 
Posts: 1471
Joined: Fri Oct 12, 2007 6:06 am
Location: France

Re: PCB DESIGN - All In One v2.5 - 32 inputs with 74HC4851

Postby mrdutx » Wed Oct 07, 2009 5:55 pm

Synthex wrote:
mrdutx wrote:i love to buy it. but i don't have pay pal and live in malaysia. it pretty hard to me to buy it.

You can pay by bank transfer if you want.

it's possible?
i realy don't know how
mrdutx
 
Posts: 23
Joined: Wed Sep 23, 2009 3:57 am

Re: PCB DESIGN - All In One v2.5 - 32 inputs with 74HC4851

Postby Firelord » Wed Oct 07, 2009 6:22 pm

mrdutx wrote:yes..it hv been invert..this process is not finish yet. this just develop process..after itching process it will be invert back..
yess..yellow are copper..

Ok, sorry, I thought this is what you got AFTER etching.

What exactly did you use to transfer the toner?
Firelord
 
Posts: 666
Joined: Wed Jun 10, 2009 7:50 pm
Location: Estonia

Re: PCB DESIGN - All In One v2.5 - 32 inputs with 74HC4851

Postby mrdutx » Wed Oct 07, 2009 6:27 pm

Firelord wrote:
mrdutx wrote:yes..it hv been invert..this process is not finish yet. this just develop process..after itching process it will be invert back..
yess..yellow are copper..

Ok, sorry, I thought this is what you got AFTER etching.

What exactly did you use to transfer the toner?


i use high UV exposure..(if i'm not wrong)
mrdutx
 
Posts: 23
Joined: Wed Sep 23, 2009 3:57 am

Re: PCB DESIGN - All In One v2.5 - 32 inputs with 74HC4851

Postby Firelord » Wed Oct 07, 2009 7:06 pm

mrdutx wrote:i use high UV exposure..(if i'm not wrong)

Oh, so you must be using photoresist then? Unfortunately, I do not use photoresist myself because I find it somewhat expensive and generally not as easy to use as direct toner tranfer (using an electric iron). So I can't really suggest a solid solution.

It might be that you've underexposed the board (i.e. didn't hold it under UV light for long enough), or maybe the photoresist cover was not evenly distributed across the board.
Firelord
 
Posts: 666
Joined: Wed Jun 10, 2009 7:50 pm
Location: Estonia

Re: PCB DESIGN - All In One v2.5 - 32 inputs with 74HC4851

Postby Synthex » Wed Oct 07, 2009 9:30 pm

mrdutx wrote:
Synthex wrote:You can pay by bank transfer if you want.

it's possible?
i realy don't know how

By Swift Code / IBAN Code
Synthex
 
Posts: 1471
Joined: Fri Oct 12, 2007 6:06 am
Location: France

PreviousNext

Return to MegaDrum Hardware

Who is online

Users browsing this forum: Bing [Bot], Google [Bot] and 72 guests