>>> KIT AVAILABLE <<< All In One v2.8 PCB Kit to sell !

[Synthex]

Nobody for these Jacks PCB ?

Jacks_PCB_32i.gif

Jacks_PCB_24i.gif

[jeffbeckib]

God I feel dumber and Dumber with every one of my questions. Are these PCB's that I could use with my 2.8? or what I would use with the Next kit you're going to release?

[Synthex]

God I feel dumber and Dumber with every one of my questions. Are these PCB's that I could use with my 2.8? or what I would use with the Next kit you're going to release?

The 32i jacks PCB is 100% compatible with the v3.1 kit and the v2.8 kit.

The 24i jacks PCB is 100% compatible with the v3.1 kit and the v2.8 kit with an extension board (8 pin -> 24 inputs).

[kurtus420]

Perfect, Thanks Synthex

meaning six individually shielded cables from the extenstion on v2.8 pcb board to the daughter board? I can get 2 and 3 conductor shielded cable but not individually shielded, can the analog and digital be wired seperatly using 2) 3 conductor shielded cables?
What pins on the extension are analog and which ones are digital?

EXT Connector :
1 - VCC
2 - GND
3 - ADC4 (analog)
4 - ADC5 (analog)
5 - ADC6 (analog)
6 - PB0 (digital)
7 - PB1 (digital)
8 - PB2 (digital)

1, 2, 6, 7, 8 can be in the same shield.
3, 4, 5 must be individually shielded.

[jeffbeckib]

ok so if this 32 board works with my 2.8, I'm ready to send payment.
Would you be selling your kits with stacked jacks as well? or should I pick those up online somewhere?

Nobody for these Jacks PCB ?

Jacks_PCB_32i.gif

Jacks_PCB_24i.gif

[jman 31]

Hey Synthex, If you don't mind my asking, what program do you use to draw your boards. I may have asked before, but I don't remember if I did.

Thanks,
Jman

[Synthex]

ok so if this 32 board works with my 2.8, I'm ready to send payment.

Ok.

Would you be selling your kits with stacked jacks as well? or should I pick those up online somewhere?

I don't know yet.

[Synthex]

Hey Synthex, If you don't mind my asking, what program do you use to draw your boards.

DipTrace

[jman 31]

Hey Synthex, If you don't mind my asking, what program do you use to draw your boards.

DipTrace

Thanks, now that you said it I think I have asked you before.

[kurtus420]

would it be ok to use 2 conductor overall shielded cable and just omit 1 wire for pins 3, 4, and 5?

meaning six individually shielded cables from the extenstion on v2.8 pcb board to the daughter board? I can get 2 and 3 conductor shielded cable but not individually shielded, can the analog and digital be wired seperatly using 2) 3 conductor shielded cables?
What pins on the extension are analog and which ones are digital?

EXT Connector :
1 - VCC
2 - GND
3 - ADC4 (analog)
4 - ADC5 (analog)
5 - ADC6 (analog)
6 - PB0 (digital)
7 - PB1 (digital)
8 - PB2 (digital)

1, 2, 6, 7, 8 can be in the same shield.
3, 4, 5 must be individually shielded.